Division algorithm

A division algorithm is an algorithm which, given two integers N and D (respectively the numerator and the denominator), computes their quotient and/or remainder, the result of Euclidean division. Some are applied by hand, while others are employed by digital circuit designs and software.

Division algorithms fall into two main categories: slow division and fast division. Slow division algorithms produce one digit of the final quotient per iteration. Examples of slow division include restoring, non-performing restoring, non-restoring, and SRT division. Fast division methods start with a close approximation to the final quotient and produce twice as many digits of the final quotient on each iteration.^[1] Newton–Raphson and Goldschmidt algorithms fall into this category.

Variants of these algorithms allow using fast multiplication algorithms. It results that, for large integers, the computer time needed for a division is the same, up to a constant factor, as the time needed for a multiplication, whichever multiplication algorithm is used.

Discussion will refer to the form $N/D=(Q,R)$ , where

N = numerator (dividend)
D = denominator (divisor)

is the input, and

Q = quotient
R = remainder

is the output.

Division by repeated subtraction

The simplest division algorithm, historically incorporated into a greatest common divisor algorithm presented in Euclid's Elements, Book VII, Proposition 1, finds the remainder given two positive integers using only subtractions and comparisons:

function divide_unsigned(N, D)
    if D = 0 then error(DivisionByZero) end
    R := N
    Q := 0
    while R ≥ D do
        R := R − D
        Q := Q + 1
    end
    return (Q, R)
end

The proof that the quotient and remainder exist and are unique (described at Euclidean division) gives rise to a complete division algorithm, applicable to both negative and positive numbers, using additions, subtractions, and comparisons:

function divide(N, D)
  if D = 0 then error(DivisionByZero) end
  if D < 0 then 
    (Q, R) := divide(N, −D)
     return (−Q, R) 
  end
  if N < 0 then
    (Q, R) := divide(−N, D)
    if R = 0 then 
        return (−Q, 0)
    else
        -- Example: N = -7, D = 3
        -- divide(-N, D) = divide(7, 3) = (2, 1)
        -- R ≠ 0, so return (-2 - 1, 3 - 1) = (-3, 2)
        -- Check: (-3)*3 + 2 = -7
        return (−Q − 1, D − R) 
    end
  end
  -- At this point, N ≥ 0 and D > 0
  return divide_unsigned(N, D)
end

This procedure always produces R ≥ 0. Although very simple, it takes Ω(Q) steps, and so is exponentially slower than even slow division algorithms like long division. It is useful if Q is known to be small (being an output-sensitive algorithm), and can serve as an executable specification.

Alternative implementation

An alternative implementation increments a remainder and resets it when it reaches the divisor.

For $x,y\in \mathbb {N} _{0}$ , the algorithm computes $q,r\,$ such that $x=qy+r\,$ , with $0\leq r<y$ :

\operatorname {div} (x,y)=\left\lfloor x/y\right\rfloor

x{\bmod {y}}=x-y\left\lfloor x/y\right\rfloor

Consider this code in Python:

def divide_unsigned2(numerator: int, denominator: int) -> tuple[int, int]
    quotient: int = 0
    remainder: int = 0
    for _ in range(numerator):
        remainder += 1
        if remainder == denominator:
            quotient += 1
            remainder = 0
    return quotient, remainder

Notes

Special cases are

x{\bmod {1}}=0

and

x{\bmod {0}}=x

.^[2]

Variable quotient is never read. So when its assignments —highlighted— are removed from the code and quotient is removed from the output list, divide_unsigned2, like divide_unsigned, still will compute $x{\bmod {y}}$ .

Alternative implementation as counter machine
A simple counter machine (CM) can be based on the alternative implementation. The CM instructions are^[3]^[4]

Z (n): Replace r_n by 0.
S (n): Add 1 to r_n.
J (m, n, q): If r_m = r_n, jump to the qth instruction; otherwise go on to the next instruction in the program.

The counter machine program is^[5]

1: J(1,5,0)
2: S(4)
3: J(4,2,6)
4: S(5)
5: J(0,0,1)
6: S(3)
7: Z(4)
8: S(5)
9: J(0,0,1)

After the CM finishes the computation on initial register values R1=N, R2=D (remaining registers = 0),

Long division

Long division is the standard algorithm used for pen-and-paper division of multi-digit numbers expressed in decimal notation. It shifts gradually from the left to the right end of the dividend, subtracting the largest possible multiple of the divisor (at the digit level) at each stage; the multiples then become the digits of the quotient, and the final difference is then the remainder.

When used with a binary radix, this method forms the basis for the (unsigned) integer division with remainder algorithm below. Short division is an abbreviated form of long division suitable for one-digit divisors. Chunking – also known as the partial quotients method or the hangman method – is a less-efficient form of long division which may be easier to understand. By allowing one to subtract more multiples than what one currently has at each stage, a more freeform variant of long division can be developed as well.

Integer division (unsigned) with remainder

The following algorithm, the binary version of the famous long division, will divide N by D, placing the quotient in Q and the remainder in R. In the following pseudo-code, all values are treated as unsigned integers.

if D = 0 then error(DivisionByZeroException) end
Q := 0                  -- Initialize quotient and remainder to zero
R := 0                     
for i := n − 1 .. 0 do  -- Where n is number of bits in N
  R := R << 1           -- Left-shift R by 1 bit
  R(0) := N(i)          -- Set the least-significant bit of R equal to bit i of the numerator
  if R ≥ D then
    R := R − D
    Q(i) := 1
  end
end

Example

If we take N=1100₂ (12₁₀) and D=100₂ (4₁₀)

Step 1: Set R=0 and Q=0
Step 2: Take i=3 (one less than the number of bits in N)
Step 3: R=00 (left shifted by 1)
Step 4: R=01 (setting R(0) to N(i))
Step 5: R < D, so skip statement

Step 2: Set i=2
Step 3: R=010
Step 4: R=011
Step 5: R < D, statement skipped

Step 2: Set i=1
Step 3: R=0110
Step 4: R=0110
Step 5: R>=D, statement entered
Step 5b: R=10 (R−D)
Step 5c: Q=10 (setting Q(i) to 1)

Step 2: Set i=0
Step 3: R=100
Step 4: R=100
Step 5: R>=D, statement entered
Step 5b: R=0 (R−D)
Step 5c: Q=11 (setting Q(i) to 1)

end
Q=11₂ (3₁₀) and R=0.

Slow division methods

Slow division methods are all based on a standard recurrence equation^[6]

R_{j+1}=B\times R_{j}-q_{n-(j+1)}\times D,

where:

R_j is the j-th partial remainder of the division (R(0) := N(i) step is included)
B is the radix (base, usually 2 internally in computers and calculators)
q_{n − (j + 1)} is the digit of the quotient in position n−(j+1), where the digit positions are numbered from least-significant 0 to most significant n−1
n is number of digits in the quotient
D is the divisor

Restoring division

Restoring division operates on fixed-point fractional numbers and depends on the assumption 0 < D < N.^{[citation needed]}

The quotient digits q are formed from the digit set {0,1}.

The basic algorithm for binary (radix 2) restoring division is:

R := N
D := D << n            -- R and D need twice the word width of N and Q
for i := n − 1 .. 0 do  -- For example 31..0 for 32 bits
  R := 2 * R − D          -- Trial subtraction from shifted value (multiplication by 2 is a shift in binary representation)
  if R >= 0 then
    q(i) := 1          -- Result-bit 1
  else
    q(i) := 0          -- Result-bit 0
    R := R + D         -- New partial remainder is (restored) shifted value
  end
end

-- Where: N = numerator, D = denominator, n = #bits, R = partial remainder, q(i) = bit #i of quotient

Non-performing restoring division is similar to restoring division except that the value of 2R is saved, so D does not need to be added back in for the case of R < 0.

Non-restoring division

Non-restoring division uses the digit set {−1, 1} for the quotient digits instead of {0, 1}. The algorithm is more complex, but has the advantage when implemented in hardware that there is only one decision and addition/subtraction per quotient bit; there is no restoring step after the subtraction,^[7] which potentially cuts down the numbers of operations by up to half and lets it be executed faster.^[8] The basic algorithm for binary (radix 2) non-restoring division of non-negative numbers is:^{[verification needed]}

-- Inputs: N (Numerator), D (Denominator)
-- n = number of bits
-- R and D are usually stored in registers of width 2n or similar to handle shifts

R := N                      -- Initialize Remainder

for i = n − 1 .. 0 do       -- for example 31..0 for 32 bits
    -- Shift Remainder Left (Algebraically: 2 * R)
    if R >= 0 then
        R := 2 * R - D;    -- Subtract D
        q(i) := 1;         -- Record quotient bit as 1
    else
        R := 2 * R + D;    -- Add D (restore)
        q(i) := -1;        -- Record quotient bit as -1
    end if
end for

Following this algorithm, the quotient is in a non-standard form consisting of digits of −1 and +1. This form needs to be converted to binary to form the final quotient. Example:

Convert the following quotient to the digit set {0,1}:
Start:	$Q=111{\bar {1}}1{\bar {1}}1{\bar {1}}$
1. Form the positive term:	$P=11101010\,$
2. Mask the negative term:^{[note 1]}	$M=00010101\,$
3. Subtract: $P-M$ :	$Q=11010101\,$
↑ Signed binary notation with ones' complement without two's complement.

If the −1 digits of $Q$ are stored as zeros (0) as is common, then $P$ is $Q$ and computing $M$ is trivial: perform a ones' complement (bit by bit complement) on the original $Q$ .

Q := Q − bit.bnot(Q)      -- Appropriate if −1 digits in Q are represented as zeros as is common.

Finally, quotients computed by this algorithm are always odd, and the remainder in R is in the range −D ≤ R < D. For example, 5 / 2 = 3 R −1. To convert to a positive remainder, do a single restoring step after Q is converted from non-standard form to standard form:

if R < 0 then
  Q := Q − 1
  R := R + D  -- Needed only if the remainder is of interest.
end if

The actual remainder is R >> n. (As with restoring division, the low-order bits of R are used up at the same rate as bits of the quotient Q are produced, and it is common to use a single shift register for both.)

SRT division

SRT division is a popular method for division in many microprocessor implementations.^[9]^[10] The algorithm is named after D. W. Sweeney of IBM, James E. Robertson of University of Illinois, and K. D. Tocher of Imperial College London. They all developed the algorithm independently at approximately the same time (published in February 1957, September 1958, and January 1958 respectively).^[11]^[12]^[13]

SRT division is similar to non-restoring division, but it uses a lookup table based on the dividend and the divisor to determine each quotient digit.

The most significant difference is that a redundant representation is used for the quotient. For example, when implementing radix-4 SRT division, each quotient digit is chosen from five possibilities: −2, −1, 0, +1, or +2. Because of this, the choice of a quotient digit need not be perfect; later quotient digits can correct for slight errors. (For example, the quotient digit pairs (0, +2) and (1, −2) are equivalent, since 0 × 4 + 2 = 1 × 4 − 2.) This tolerance allows quotient digits to be selected using only a few most-significant bits of the dividend and divisor, rather than requiring a full-width subtraction. This simplification in turn allows a radix higher than 2 to be used.

Like non-restoring division, the final steps are a final full-width subtraction to resolve the last quotient bit, and conversion of the quotient to standard binary form.

The original Intel Pentium processor's infamous floating-point division bug was caused by an incorrectly coded lookup table. Pentium processors used a 2048-cell table, of which 1066 cells were to be populated, and values from five cells were mistakenly omitted.^[14]^[15]^[16]

Fast division methods

Newton–Raphson division

Newton–Raphson uses Newton's method to find the reciprocal of $D$ and multiply that reciprocal by $N$ to find the final quotient $Q$ .

The steps of Newton–Raphson division are:

Calculate an estimate $X_{0}$ for the reciprocal $1/D$ of the divisor $D$ .
Compute successively more accurate estimates $X_{1},X_{2},\ldots ,X_{S}$ of the reciprocal. This is where one employs the Newton–Raphson method as such.
Compute the quotient by multiplying the dividend by the reciprocal of the divisor: $Q=NX_{S}$ .

In order to apply Newton's method to find the reciprocal of $D$ , it is necessary to find a function $f(X)$ that has a zero at $X=1/D$ . The obvious such function is $f(X)=DX-1$ , but the Newton–Raphson iteration for this is unhelpful, since it cannot be computed without already knowing the reciprocal of $D$ (moreover it attempts to compute the exact reciprocal in one step, rather than allow for iterative improvements). A function that does work is $f(X)=(1/X)-D$ , for which the Newton–Raphson iteration gives

X_{i+1}=X_{i}-{f(X_{i}) \over f'(X_{i})}=X_{i}-{1/X_{i}-D \over -1/X_{i}^{2}}=X_{i}+X_{i}(1-DX_{i})=X_{i}(2-DX_{i}),

which can be calculated from $X_{i}$ using only multiplication and subtraction, or using two fused multiply–adds.

From a computation point of view, the expressions $X_{i+1}=X_{i}+X_{i}(1-DX_{i})$ and $X_{i+1}=X_{i}(2-DX_{i})$ are not equivalent. To obtain a result with a precision of 2n bits while making use of the second expression, one must compute the product between $X_{i}$ and $(2-DX_{i})$ with double the given precision of $X_{i}$ (n bits).^{[citation needed]} In contrast, the product between $X_{i}$ and $(1-DX_{i})$ need only be computed with a precision of n bits, because the leading n bits (after the binary point) of $(1-DX_{i})$ are zeros.

If the error is defined as $\varepsilon _{i}=1-DX_{i}$ , then:

{\begin{aligned}\varepsilon _{i+1}&=1-DX_{i+1}\\&=1-D(X_{i}(2-DX_{i}))\\&=1-2DX_{i}+D^{2}X_{i}^{2}\\&=(1-DX_{i})^{2}\\&={\varepsilon _{i}}^{2}.\\\end{aligned}}

This squaring of the error at each iteration step – the so-called quadratic convergence of Newton–Raphson's method – has the effect that the number of correct digits in the result roughly doubles for every iteration, a property that becomes extremely valuable when the numbers involved have many digits (e.g. in the large integer domain). But it also means that the initial convergence of the method can be comparatively slow, especially if the initial estimate $X_{0}$ is poorly chosen.

Initial estimate

For the subproblem of choosing an initial estimate $X_{0}$ , it is convenient to apply a bit-shift to the divisor D to scale it so that 0.5 ≤ D ≤ 1. Applying the same bit-shift to the numerator N ensures the quotient does not change. Once within a bounded range, a simple polynomial approximation can be used to find an initial estimate.

The linear approximation with minimum worst-case absolute error on the interval $[0.5,1]$ is:

X_{0}={48 \over 17}-{32 \over 17}D.

The coefficients of the linear approximation $T_{0}+T_{1}D$ are determined as follows. The absolute value of the error is $|\varepsilon _{0}|=|1-D(T_{0}+T_{1}D)|$ . The minimum of the maximum absolute value of the error is determined by the Chebyshev equioscillation theorem applied to $F(D)=1-D(T_{0}+T_{1}D)$ . The local minimum of $F(D)$ occurs when $F'(D)=0$ , which has solution $D=-T_{0}/(2T_{1})$ . The function at that minimum must be of opposite sign as the function at the endpoints, namely, $F(1/2)=F(1)=-F(-T_{0}/(2T_{1}))$ . The two equations in the two unknowns have a unique solution $T_{0}=48/17$ and $T_{1}=-32/17$ , and the maximum error is $F(1)=1/17$ . Using this approximation, the absolute value of the error of the initial value is less than

\vert \varepsilon _{0}\vert \leq {1 \over 17}\approx 0.059.

The best quadratic fit to $1/D$ in the interval is

X:={\frac {140}{33}}-{\frac {64}{11}}D+{\frac {256}{99}}D^{2}.

It is chosen to make the error equal to a re-scaled third order Chebyshev polynomial of the first kind, and gives an absolute value of the error less than or equal to 1/99. This improvement is equivalent to $\log _{2}(\log 99/\log 17)\approx 0.7$ Newton–Raphson iterations, at a computational cost of less than one iteration.

It is possible to generate a polynomial fit of degree larger than 2, computing the coefficients using the Remez algorithm. The trade-off is that the initial guess requires more computational cycles but hopefully in exchange for fewer iterations of Newton–Raphson.

Since for this method the convergence is exactly quadratic, it follows that, from an initial error $\varepsilon _{0}$ , $S$ iterations will give an answer accurate to

P=-2^{S}\log _{2}\varepsilon _{0}-1=2^{S}\log _{2}(1/\varepsilon _{0})-1

binary places. Typical values are:

Binary digits of reciprocal accuracy
$\varepsilon _{0}$	Iterations
$\varepsilon _{0}$	0	1	2	3	4
$1/17$	3.09	7.17	15.35	31.70	64.40
$1/99$	5.63	12.26	25.52	52.03	105.07

A quadratic initial estimate plus two iterations is accurate enough for IEEE single precision, but three iterations are marginal for double precision. A linear initial estimate plus four iterations is sufficient for both double and double extended formats.

Pseudocode

The following computes the quotient of N and D with a precision of P binary places:

Express D as M × 2e where 1 ≤ M < 2 (standard floating point representation)

D' := D / 2e+1   // scale between 0.5 and 1, can be performed with bit shift / exponent subtraction

N' := N / 2e+1

X := 48/17 − 32/17 × D'   // precompute constants with same precision as D

repeat 
  
          ⌈
          
              log
              
                2
              
            ⁡
            
                  P
                  +
                  1
                
                    log
                    
                      2
                    
                  ⁡
                  17
                
          ⌉
        
    {\displaystyle \left\lceil \log _{2}{\frac {P+1}{\log _{2}17}}\right\rceil \,}
  
 times   // can be precomputed based on fixed P

X := X + X × (1 - D' × X)

end

return N' × X

For example, for a double-precision floating-point division, this method uses 10 multiplies, 9 adds, and 2 shifts.

Cubic iteration

There is an iteration which uses three multiplications to cube the error:

\varepsilon _{i}=1-DX_{i}

Y_{i}=X_{i}\varepsilon _{i}

X_{i+1}=X_{i}+Y_{i}+Y_{i}\varepsilon _{i}.

The Y_iε_i term is new.

Expanding out the above, $X_{i+1}$ can be written as

{\begin{aligned}X_{i+1}&=X_{i}+X_{i}\varepsilon _{i}+X_{i}\varepsilon _{i}^{2}\\&=X_{i}+X_{i}(1-DX_{i})+X_{i}(1-DX_{i})^{2}\\&=3X_{i}-3DX_{i}^{2}+D^{2}X_{i}^{3},\end{aligned}}

with the result that the error term

{\begin{aligned}\varepsilon _{i+1}&=1-DX_{i+1}\\&=1-3DX_{i}+3D^{2}X_{i}^{2}-D^{3}X_{i}^{3}\\&=(1-DX_{i})^{3}\\&=\varepsilon _{i}^{3}.\end{aligned}}

This is 3/2 the computation of the quadratic iteration, but achieves $\log 3/\log 2\approx 1.585$ as much convergence, so is slightly more efficient. Put another way, two iterations of this method raise the error to the ninth power at the same computational cost as three quadratic iterations, which only raise the error to the eighth power.

The number of correct bits after $S$ iterations is

P=-3^{S}\log _{2}\varepsilon _{0}-1=3^{S}\log _{2}(1/\varepsilon _{0})-1

binary places. Typical values are:

Bits of reciprocal accuracy
$\varepsilon _{0}$	Iterations
$\varepsilon _{0}$	0	1	2	3
$1/17$	3.09	11.26	35.79	109.36
$1/99$	5.63	18.89	58.66	177.99

A quadratic initial estimate plus two cubic iterations provides ample precision for an IEEE double-precision result. It is also possible to use a mixture of quadratic and cubic iterations.

Using at least one quadratic iteration ensures that the error is positive, i.e. the reciprocal is underestimated.^[17]^: 370 This can simplify a following rounding step if an exactly-rounded quotient is required.

Using higher degree polynomials in either the initialization or the iteration results in a degradation of performance because the extra multiplications required would be better spent on doing more iterations.^{[citation needed]}

Goldschmidt division

Goldschmidt division^[18] (after Robert Elliott Goldschmidt)^[19] uses an iterative process of repeatedly multiplying both the dividend and divisor by a common factor F_i, chosen such that the divisor converges to 1. This causes the dividend to converge to the sought quotient Q:

Q={\frac {N}{D}}{\frac {F_{1}}{F_{1}}}{\frac {F_{2}}{F_{2}}}{\frac {F_{\ldots }}{F_{\ldots }}}.

The steps for Goldschmidt division are:

Generate an estimate for the multiplication factor F_i .
Multiply the dividend and divisor by F_i .
If the divisor is sufficiently close to 1, return the dividend, otherwise, loop to step 1.

Assuming N/D has been scaled so that 0 < D < 1, each F_i is based on D:

F_{i+1}=2-D_{i}.

Multiplying the dividend and divisor by the factor yields:

{\frac {N_{i+1}}{D_{i+1}}}={\frac {N_{i}}{D_{i}}}{\frac {F_{i+1}}{F_{i+1}}}.

After a sufficient number k of iterations $Q=N_{k}$ .

The Goldschmidt method is used in AMD Athlon CPUs and later models.^[20]^[21] It is also known as Anderson Earle Goldschmidt Powers (AEGP) algorithm and is implemented by various IBM processors.^[22]^[23] Although it converges at the same rate as a Newton–Raphson implementation, one advantage of the Goldschmidt method is that the multiplications in the numerator and in the denominator can be done in parallel.^[23]

Binomial theorem

The Goldschmidt method can be used with factors that allow simplifications by the binomial theorem. Assume ⁠ $N/D$ ⁠ has been scaled by a power of two such that $D\in \left({\tfrac {1}{2}},1\right]$ . We choose $D=1-x$ and $F_{i}=1+x^{2^{i}}$ . This yields

{\frac {N}{1-x}}={\frac {N\cdot (1+x)}{1-x^{2}}}={\frac {N\cdot (1+x)\cdot (1+x^{2})}{1-x^{4}}}=\cdots =Q'={\frac {N'=N\cdot (1+x)\cdot (1+x^{2})\cdot \cdot \cdot (1+x^{2^{(n-1)}})}{D'=1-x^{2^{n}}\approx 1}}

After $n$ steps $\left(x\in \left[0,{\tfrac {1}{2}}\right)\right)$ , the denominator $1-x^{2^{n}}$ can be rounded to 1 with a relative error

\varepsilon _{n}={\frac {Q'-N'}{Q'}}=x^{2^{n}}

which is maximum at $2^{-2^{n}}$ when $x={\tfrac {1}{2}}$ , thus providing a minimum precision of $2^{n}$ binary digits.

Large-integer methods

Methods designed for hardware implementation generally do not scale to integers with thousands or millions of decimal digits; these frequently occur, for example, in modular reductions in cryptography. For these large integers, more efficient division algorithms transform the problem to use a small number of multiplications, which can then be done using an asymptotically efficient multiplication algorithm such as the Karatsuba algorithm, Toom–Cook multiplication or the Schönhage–Strassen algorithm. The result is that the computational complexity of the division is of the same order (up to a multiplicative constant) as that of the multiplication. Examples include reduction to multiplication by Newton's method as described above,^[24] as well as the slightly faster Burnikel-Ziegler division,^[25] Barrett reduction and Montgomery reduction algorithms.^[26]^{[verification needed]} Newton's method is particularly efficient in scenarios where one must divide by the same divisor many times, since after the initial Newton inversion only one (truncated) multiplication is needed for each division.

Division by a constant

The division by a constant D is equivalent to the multiplication by its reciprocal. Since the denominator is constant, so is its reciprocal (1/D). Thus it is possible to compute the value of (1/D) once at compile time, and at run time perform the multiplication N·(1/D) rather than the division N/D. In floating-point arithmetic the use of (1/D) presents little problem,^[a] but in integer arithmetic the reciprocal will always evaluate to zero (assuming |D| > 1).

It is not necessary to use specifically (1/D); any value (X/Y) that reduces to (1/D) may be used. For example, for division by 3, the factors 1/3, 2/6, 3/9, or 194/582 could be used. Consequently, if Y were a power of two the division step would reduce to a fast right bit shift. The effect of calculating N/D as (N·X)/Y replaces a division with a multiply and a shift. Note that the parentheses are important, as N·(X/Y) will evaluate to zero.

However, unless D itself is a power of two, there is no X and Y that satisfies the conditions above. Fortunately, (N·X)/Y gives exactly the same result as N/D in integer arithmetic even when (X/Y) is not exactly equal to 1/D, but "close enough" that the error introduced by the approximation is in the bits that are discarded by the shift operation.^[27]^[28]^[29] Barrett reduction uses powers of 2 for the value of Y to make division by Y a simple right shift.^[b]

As a concrete fixed-point arithmetic example, for 32-bit unsigned integers, division by 3 can be replaced with a multiply by ⁠2863311531/2³³⁠, a widening multiplication by 2863311531 (hexadecimal 0xAAAAAAAB) followed by a 33 right bit shift. The value of 2863311531 is calculated as ⁠2³³/3⁠, then rounded up. Likewise, division by 10 can be expressed as a multiplication by 3435973837 (0xCCCCCCCD) followed by division by 2³⁵ (or 35 right bit shift).^[31]^: p230-234 OEIS provides sequences of the constants for multiplication as A346495 and for the right shift as A346496.

For general $x$ -bit unsigned integer division where the divisor $D$ is not a power of 2, the following identity converts the division into two $x$ -bit addition/subtraction, one $x$ -bit by $x$ -bit multiplication (where only the upper half of the result is used) and several shifts, after precomputing $k=x+\lceil \log _{2}{D}\rceil$ and $a=\left\lceil {\frac {2^{k}}{D}}\right\rceil -2^{x}$ :

\left\lfloor {\frac {N}{D}}\right\rfloor =\left\lfloor {\frac {\left\lfloor {\frac {N-b}{2}}\right\rfloor +b}{2^{k-x-1}}}\right\rfloor {\text{ where }}b=\left\lfloor {\frac {Na}{2^{x}}}\right\rfloor

In some cases, division by a constant can be accomplished in even less time by converting the "multiply by a constant" into a series of shifts and adds or subtracts.^[32] Of particular interest is division by 10, for which the exact quotient is obtained, with remainder if required.^[33]

Rounding error

This section needs expansion. You can help by adding missing information. (September 2012)

When a division operation is performed, the exact quotient $q$ and remainder $r$ are approximated to fit within the computer's precision limits. The Division Algorithm states:

$[a=bq+r]$

where $0\leq r<|b|$ .

In floating-point arithmetic, the quotient $q$ is represented as ${\tilde {q}}$ and the remainder $r$ as ${\tilde {r}}$ , introducing rounding errors $\epsilon _{q}$ and $\epsilon _{r}$ :

$[{\tilde {q}}=q+\epsilon _{q}][{\tilde {r}}=r+\epsilon _{r}]$

This rounding causes a small error, which can propagate and accumulate through subsequent calculations. Such errors are particularly pronounced in iterative processes and when subtracting nearly equal values - is told loss of significance. To mitigate these errors, techniques such as the use of guard digits or higher precision (or arbitrary precision) are employed.^[34]^[35]

Notes

↑ Despite how "little" problem the optimization causes, this reciprocal optimization is still usually hidden behind a "fast math" flag in modern compilers as it is inexact.
↑ Modern compilers commonly perform this integer multiply-and-shift optimization; for a constant only known at run-time, however, the program must implement the optimization itself.^[30]

References

↑ Rodeheffer, Thomas L. (2008-08-26). Software Integer Division (PDF) (Technical report). Microsoft Research, Silicon Valley.
↑ Compare: in procedure divide_unsigned, denominator must be strictly positive.
↑ Shepherdson, J.C.; Sturgis, H.E. (1963). "Computability of Recursive Functions". Journal of the Association for Computing Machinery. 10 (2): 217–255. doi:10.1145/321160.321170.
↑ Cutland, Nigel (1980). Computability: An Introduction to Recursive Function Theory (PDF). Cambridge University Press. p. 12. ISBN 978-0-521-22384-3. Retrieved 2025-09-16.
↑ The code runs on "URM Simulator". Occidental College, Los Angeles. Unlimited Register Machine (URM) simulator (emulator) -- a "virtual URM". It is modeled after the URM specification in Nigel J. Cutland's book, Computability, An introduction to recursive function theory, by Cambridge Press.
↑ Morris, James E.; Iniewski, Krzysztof (2017-11-22). Nanoelectronic Device Applications Handbook. CRC Press. ISBN 978-1-351-83197-0.
↑ Shaw, Robert F. (1950). "Arithmetic Operations in a Binary Computer". Review of Scientific Instruments. 21 (8): 690. Bibcode:1950RScI...21..687S. doi:10.1063/1.1745692. ISSN 0034-6748. Archived from the original on 2022-02-28. Retrieved 2022-02-28.
↑ Flynn. "Stanford EE486 (Advanced Computer Arithmetic Division) – Chapter 5 Handout (Division)" (PDF). Stanford University. Archived (PDF) from the original on 2022-04-18. Retrieved 2019-06-24.
↑ Harris, David L.; Oberman, Stuart F.; Horowitz, Mark A. (9 September 1998). SRT Division: Architectures, Models, and Implementations (PDF) (Technical report). Stanford University. Archived (PDF) from the original on 24 December 2016. Retrieved 23 December 2016.
↑ McCann, Mark; Pippenger, Nicholas (2005). "SRT Division Algorithms as Dynamical Systems". SIAM Journal on Computing. 34 (6): 1279–1301. doi:10.1137/S009753970444106X. hdl:2429/12179. Archived from the original on 2022-08-24. Retrieved 2022-08-24.
↑ Cocke, John; Sweeney, D.W. (11 February 1957), High speed arithmetic in a parallel device (Company Memo), IBM, p. 20, archived from the original on 24 August 2022, retrieved 24 August 2022{{citation}}: CS1 maint: location missing publisher (link)
↑ Robertson, James (1958-09-01). "A New Class of Digital Division Methods". IRE Transactions on Electronic Computers. EC-7 (3). IEEE: 218–222. Bibcode:1958IRTEC...7..218R. doi:10.1109/TEC.1958.5222579. hdl:2027/uiuo.ark:/13960/t0gt7529c.
↑ Tocher, K.D. (1958-01-01). "Techniques of Multiplication and Division for Automatic Binary Computers". The Quarterly Journal of Mechanics and Applied Mathematics. 11 (3): 364–384. doi:10.1093/qjmam/11.3.364. Archived from the original on 2022-08-24. Retrieved 2022-08-24.
↑ "Statistical Analysis of Floating Point Flaw". Intel Corporation. 1994. Archived from the original on 23 October 2013. Retrieved 22 October 2013.
↑ Oberman, Stuart F.; Flynn, Michael J. (July 1995). An Analysis of Division Algorithms and Implementations (PDF) (Technical report). Stanford University. CSL-TR-95-675. Archived (PDF) from the original on 2017-05-17. Retrieved 2016-12-23.
↑ Shirriff, Ken (28 Dec 2024). "Intel's $475 million error: the silicon behind the Pentium division bug". Righto. Retrieved 30 Dec 2024.
↑ Ercegovac, Miloš D.; Lang, Tomás (2004). "Chapter 7: Reciprocal. Division, Reciprocal Square Root, and Square Root by Iterative Approximation". Digital Arithmetic. Morgan Kaufmann. pp. 367–395. ISBN 1-55860-798-6.
↑ Goldschmidt, Robert E. (1964). Applications of Division by Convergence (PDF) (Thesis). M.Sc. dissertation. M.I.T. OCLC 34136725. Archived (PDF) from the original on 2015-12-10. Retrieved 2015-09-15.
↑ "Authors". IBM Journal of Research and Development. 11: 125–127. 1967. doi:10.1147/rd.111.0125. Archived from the original on 18 July 2018.
↑ Oberman, Stuart F. (1999). "Floating point division and square root algorithms and implementation in the AMD-K7 Microprocessor" (PDF). Proceedings 14th IEEE Symposium on Computer Arithmetic (Cat. No.99CB36336). pp. 106–115. doi:10.1109/ARITH.1999.762835. ISBN 0-7695-0116-8. S2CID 12793819. Archived (PDF) from the original on 2015-11-29. Retrieved 2015-09-15.
↑ Soderquist, Peter; Leeser, Miriam (July–August 1997). "Division and Square Root: Choosing the Right Implementation". IEEE Micro. 17 (4): 56–66. Bibcode:1997IMicr..17d..56S. doi:10.1109/40.612224.
↑ S. F. Anderson, J. G. Earle, R. E. Goldschmidt, D. M. Powers. The IBM 360/370 model 91: floating-point execution unit, IBM Journal of Research and Development, January 1997
1 2 Guy, Even; Peter, Siedel; Ferguson, Warren (1 February 2005). "A parametric error analysis of Goldschmidt's division algorithm". Journal of Computer and System Sciences. 70 (1): 118–139. doi:10.1016/j.jcss.2004.08.004.
↑ Hasselström, Karl (2003). Fast Division of Large Integers: A Comparison of Algorithms (PDF) (M.Sc. in Computer Science thesis). Royal Institute of Technology. Archived from the original (PDF) on 8 July 2017. Retrieved 2017-07-08.
↑ Joachim Ziegler, Christoph Burnikel (1998), Fast Recursive Division, Max-Planck-Institut für Informatik, archived from the original on 2011-04-26, retrieved 2021-09-10{{citation}}: CS1 maint: location missing publisher (link)
↑ Barrett, Paul (1987). "Implementing the Rivest Shamir and Adleman public key encryption algorithm on a standard digital signal processor". Proceedings on Advances in cryptology---CRYPTO '86. London, UK: Springer-Verlag. pp. 311–323. ISBN 0-387-18047-8.
↑ Granlund, Torbjörn; Montgomery, Peter L. (June 1994). "Division by Invariant Integers using Multiplication" (PDF). SIGPLAN Notices. 29 (6): 61–72. doi:10.1145/773473.178249. Archived (PDF) from the original on 2019-06-06. Retrieved 2015-12-08.
↑ Möller, Niels; Granlund, Torbjörn (February 2011). "Improved Division by Invariant Integers" (PDF). IEEE Transactions on Computers. 60 (2): 165–175. Bibcode:2011ITCmp..60..165M. doi:10.1109/TC.2010.143. S2CID 13347152. Archived (PDF) from the original on 2015-12-22. Retrieved 2015-12-08.
↑ ridiculous_fish. "Labor of Division (Episode III): Faster Unsigned Division by Constants" Archived 2022-01-08 at the Wayback Machine. 2011.
↑ ridiculous_fish. "libdivide, optimized integer division". Archived from the original on 23 November 2021. Retrieved 6 July 2021.
↑ Warren Jr., Henry S. (2013). Hacker's Delight (2 ed.). Addison Wesley - Pearson Education, Inc. ISBN 978-0-321-84268-8.
↑ LaBudde, Robert A.; Golovchenko, Nikolai; Newton, James; and Parker, David; Massmind: "Binary Division by a Constant" Archived 2022-01-09 at the Wayback Machine
↑ Vowels, R. A. (1992). "Division by 10". Australian Computer Journal. 24 (3): 81–85.
↑ L. Popyack, Jeffrey (June 2000). "Rounding Error". Drexel University.
↑ "9. Machine Numbers, Rounding Error and Error Propagation". College of Charleston. 8 February 2021.

v t e Number-theoretic algorithms
Primality tests	AKS APR Baillie–PSW Elliptic curve Pocklington Fermat Lucas Lucas–Lehmer Lucas–Lehmer–Riesel Proth's theorem Pépin's Quadratic Frobenius Solovay–Strassen Miller–Rabin
Prime-generating	Sieve of Atkin Sieve of Eratosthenes Sieve of Pritchard Sieve of Sundaram Wheel factorization
Integer factorization	Continued fraction (CFRAC) Dixon's Lenstra elliptic curve (ECM) Euler's Pollard's rho p − 1 p + 1 Quadratic sieve (QS) General number field sieve (GNFS) Special number field sieve (SNFS) Rational sieve Fermat's Shanks's square forms Trial division Shor's
Multiplication	Ancient Egyptian Long Karatsuba Toom–Cook Schönhage–Strassen Fürer's
Euclidean division	Binary Chunking Fourier Goldschmidt Newton-Raphson Long Short SRT
Discrete logarithm	Baby-step giant-step Pollard rho Pollard kangaroo Pohlig–Hellman Index calculus Function field sieve
Greatest common divisor	Binary Euclidean Extended Euclidean Lehmer's
Modular square root	Cipolla Pocklington's Tonelli–Shanks Berlekamp
Other algorithms	Chakravala Cornacchia Exponentiation by squaring Integer square root Integer relation (LLL; KZ) Modular exponentiation Montgomery reduction Schoof Trachtenberg system
Italics indicate that algorithm is for numbers of special forms